Question: The two axes of an xy positioning table are each driven by a stepping motor connected to a lead screw with a 10:1 gear reduction.

The two axes of an xy positioning table are each driven by a stepping motor connected to a lead screw with a 10:1 gear reduction. The number of step angles on each stepping motor is 20. Each lead screw has a pitch = 4.5 mm and provides an axis range = 300 mm. There are 16 bits in each binary register used by the controller to store position data for the two axes.

Step by Step Solution

★★★★★

3.45 Rating (164 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

a CR 1 p r g n s 4510 x 20 00225 mm CR 2 000458 mm CR Max00225 000458 00225 mm b v t 500 ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

795-C-S-A-I (472).docx

120 KBs Word File

Students Have Also Explored These Related Artificial Intelligence Questions!

A stepping motor with 200 step angles is coupled to a lead screw through a gear reduction of 5:1 (5 rotations of the motor for each rotation of the lead screw). The lead screw has 2.4 threads/cm. The...

Stepping motors are used to drive the two axes of an insertion machine used for electronic assembly. A printed circuit board is mounted on the table which must be positioned accurately for reliable...

Two plates, each 5 mm thick, are connected by means of four rivets as shown in Fig. below. The permissible stresses for rivets and plates in tension, shear and compression are 80, 60 and 120 N/mm2...

The two axes of an xy positioning table are each driven by a stepping motor connected to a Leadscrew with a 4:1 gear reduction. The number of step angles on each stepping motor is 200. Each Leadscrew...

One axis of an NC positioning system is driven by a stepping motor. The motor is connected to a lead screw whose pitch is 4.0 mm, and the lead screw drives the table. Control resolution for the table...

7.6 (A) One axis of the worktable in a CNC positioning system is driven by a ball screw with a 6-mm pitch. The screw is powered by a stepper motor which has 180 step angles using a 2:1 gear reduction...

One axis of the worktable in a CNC positioning system is driven by a ball screw with a 6 - mm pitch. The screw is powered by a stepper motor which has 1 8 0 step angles using a 2 : 1 gear reduction (...

The Picture is the example the problem is talking about 2. Suppose the mechanical inaccuracies in the open-loop positioning system of Example 7.1 are described by a normal distribution with standard...

Hello, you already did chapter 1 and 2 of my MASTERS Thesis already for me. (See attached) So normally you know masters thesis consist of 5 chapters right ??..... But in this case my thesis will be 4...

Two stepping motors are used in an open loop system to drive the lead screws for xy positioning. The range of each axis is 250 mm. The shafts of the motors are connected directly to the lead screws....

How does a primary market differ from a secondary market? Where are most securities traded: in the primary or the secondary market?

A solid circular column is 4m long with both ends fixed, carries a safe axial load 500kN. Using Euler's equation, calculate the diameter of column. Take E=100kN/m and Factor of safety 2.5.

The Securities Exchange Act of 1 9 3 4 contains sections that deal with A ) form and content of the prospectus that must be given to all prospective purchasers of a security. B ) trading activities...

What is the distinction between an experimental group and a control group?

In protocol 3, is it possible that the sender starts the timer when it is already running? If so, how might this occur? If not, why is it impossible?

Imagine a sliding window protocol using so many bits for sequence numbers that wraparound never occurs. What relations must hold among the four window edges and the window size, which is constant and...

If the procedure between in protocol 5 checked for the condition a

The purpose of this exercise is to compare the return on Tesla stock with the return on a set of options strategies. All returns should be calculated between November 15 and November 25. The Excel...

An issue of 8.5% Series C preferred stock has a par value of $75 million or $40 per share and was sold to investors several years ago at par. According to the terms of the issue, the preferred is...

Caspian Sea Drinks is considering the production of a diet drink. The expansion of the plant and the purchase of the equipment necessary to produce the diet drink will cost $28.00 million. The plant...