Question: Write the part program to drill the holes in the part shown in Figure P7.26. The part is 12.0 mm thick. Cutting speed = 100

Write the part program to drill the holes in the part shown in Figure P7.26. The part is 12.0 mm thick. Cutting speed = 100 m/min and feed = 0.06 mm/rev. Use the lower left corner of the part as the origin in the x-y axis system. Write the part program in the word address format using absolute positioning. The program style should be similar to Example A7.1.

Step by Step Solution

★★★★★

3.45 Rating (168 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

At the beginning of the job the drill point will be positioned at a target point located at x 0 y 0 ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

795-C-S-A-I (473).docx

120 KBs Word File

Students Have Also Explored These Related Artificial Intelligence Questions!

The part is to be drilled on a turret-type drill press. The part is 15.0 mm thick. There are three drill sizes to be used: 8 mm, 10 mm, and 12 mm. These drills are to be specified in the part program...

The outline of the part in the previous problem is to be profile milled using a 30 mm diameter end mill with four teeth. The part is 15 mm thick. Cutting speed = 150 mm/min and feed = 0.085 mm/tooth....

The outline of the part in Figure P7.29 is to be profile milled, using a 20 mm diameter end mill with two teeth. The part is 10 mm thick. Cutting speed = 125 mm/min and feed = 0.10 mm/tooth. Use the...

ISE 4 7 0 HW 3 2 0 points. Due the end of 1 5 Oct. Write the part program to drill the holes in the part in Figure below ( Unit: mm ) . The part is 1 2 . 0 mm thick. Cutting speed \ ( = 1 0 0 \...

Q . 1 Part shown in Fig. is to be profile milled along the path P 1 - P 2 - P 3 - P 4 - P 5 - P 6 - P 7 - P 8 - P 9 , using a 1 2 mm diameter end mill with four teeth. The part is 1 0 mm thick....

Q . 3 : ( 1 5 pts . ) Write the part program to drill in order the holes H 1 and H 2 in the part shown in the figure. The part is 1 2 . 0 m m thick. Rotational speed of the drill is 3 1 8 0 r p m and...

Write the complete APT part program to profile mill the outside edges of the part. The part is 15 mm thick. Tooling = 30 mm diameter end mill with four teeth, cutting speed = 150 mm/min, and feed =...

Approximately how many years will it take to double a 1000 investment when the average return is 9% per year?

Let F(x, y, z) = xi + yj + zk. Evaluate the integral of F along each of the following paths. (a) c(t) = (3t, 3t, 3t), 0 t 1 (b) c(t) = (2 cos(t), 2 sin(t), 0), (c) c(t) = (2 sin(t), 0, 2 cos(t)), 0 ...

15.29 Radon detectors. How accurate are radon detectors of a type sold to homeowners? To answer this question, university researchers placed 12 detectors in a chamber that exposed them to 105...

What is the definition of a non-experimental study?

In protocol 6, when a data frame arrives, a check is made to see if the sequence number differs from the one expected and nonak is true. If both conditions hold, a NAK is sent. Otherwise, the...

Suppose that the three-statement while loop near the end of protocol 6 were removed from the code. Would this affect the correctness of the protocol or just the performance? Explain your answer.

Suppose that the case for checksum errors were removed from the switch statement of protocol 6. How would this change affect the operation of the protocol?

The two stocks in your portfolio, X and Y, have independent returns, so the correlation between them, rey is zero. Your portfolio consists of $50,000 Invested in Stock X and 550,000 invested in Stock...

You have a credit card with a balance of $12,400 and an APR of 17.6 percent compounded monthly. You have been making monthly payments of $240 per month, but you have received a substantial raise and...

age 3 of 3 2 3 Question 11 (0.2 points) Which one of the following is an example of systematic risk? 1) Major layoff by a regional manufacturer of power boats ge 2: 2) Surprise firing of a firm's...