Explain the reasons for hot tearing in castings.

Question:

Fantastic news! We've Found the answer you've been seeking!

Step by Step Answer:

Related Book For book-img-for-question

Manufacturing Processes for Engineering Materials

ISBN: 978-0132272711

5th edition

Authors: Serope Kalpakjian, Steven Schmid

See More Books

Question Posted: Jul 18, 2016 08:56 AM

See More Questions

Explain the reasons for the observed changes in blood flow velocity in the different regions of the circulation.
By using the pre-emphasis filter shown in Figure a and with a voice signal as the modulating wave, and FM transmitter produces a signal that is essentially frequency modulated by the lower audio...
Predict whether each of the following oxides is ionic or molecular: SnO2, Al2O3, CO2, Li2O, Fe2O3, H2O Explain the reasons for your choices.
Write the complete APT part program to profile mill the outside edges of the part. The part is 15 mm thick. Tooling = 30 mm diameter end mill with four teeth, cutting speed = 150 mm/min, and feed =...
Suppose that a researcher discovers that a measure of the total amount of debt in the U.S economy over the past twenty years was a predictor of inflation and the business cycle than M1 or M2. Does...
There are various investment decision rules, which financial managers may select. Choose one of the alternatives to the NPV, and compare and contrast one of the selected alternatives with NPV...
Obtain customer feedback about the project
Consider the following program: Note that the scheduler in a uniprocessor system would implement pseudo parallel execution of these two concurrent processes by interleaving their instructions,...
The following data represents information necessary to assist in preparing the September 3 0 , 2 0 2 2 bank reconciliation for Domore Company. The September 3 0 bank balance was $ 5 , 0 2 5 . The...
The trial balance of Telegraphic Link at November 30, follows: Additional information at November 30, 2012: a. Accrued service revenue, $600. b. Depreciation, $300. c. Accrued salary expense, $800....
How can you tell whether a cavity in a casting is due to porosity or to shrinkage?
Would you be concerned about the fact that a portion of an internal chill is left within the casting? What materials do you think chills should be made of, and why?
Universal Solar Ltd operates three departments a lighting department, a water heating department, and an equipment department. The stores accountant has prepared a statement of financial performance...
How do intersectionality and identity salience intersect within the framework of diversity and inclusion initiatives, and what strategies can organizations employ to address these complexities ?
(a) -2-3 3. Evaluate the following determinants: 3 5 (b) |- 58 -8 -2 4 312 4 3 0 (c) 2 245 (d) 3 1 2 245 5 -1 -4
The following information pertains to the inventory of Parvin Company for Year 3: January 1 April 1 October 1 Beginning inventory 400 units @ $22 Purchased 2,600 units @ $27 Purchased 1,200 units @...
Using partial fraction decomposition to find the partial fractions of the function 26x2 +270x+404 f(x) = f(x) = 30x3 20x2-330x 280 Hint: The denominator of f(x) can be factored as (3x+7) (5x+5)(2x-8)...
Question 1: How do strategy and tactical action relate to each other in an organization? Question 2: How can you improve the implementation of strategy in this business organization?...
Are the hourly wages that an airline pays to its maintenance workers fixed costs or variable costs?
What did Lennox gain by integrating their WMS, TMS, and labor management systems?
Not all springs are made in a conventional way. Consider the special steel spring in the illustration. (a) Find the pitch, solid height, and number of active turns. (b) Find the spring rate. Assume...
A holding fixture for a work piece 1 in thick at clamp locations is being designed. The detail of one of the clamps is shown in the figure. A spring is required to drive the clamp upward while...
Your instructor will provide you with a stock spring suppliers catalog, or pages reproduced from it. Accomplish the task of Prob. 1020 by selecting an available stock spring. (This is design by...
question 6 Timely Inc. produces luxury bags. The budgeted sales and production for the next three months are as follows july. august september Sales, in units 1,115. 1229. 1302 Production. in units...
On May 12 Zimmer Corporation placed in service equipment (seven-year property) with a basis of $220,000. This was Zimmer's only asset acquired during the year. Calculate the maximum depreciation...
Power Manufacturing has equipment that it purchased 7 years ago for $2,550,000. The equipment was used for a project that was intended to last for 9 years and was being depreciated over the life of...

Explain the reasons for hot tearing in castings.

Question:

Step by Step Answer:

Hot tearing is the result of tensile stress that that ...View the full answer

Manufacturing Processes for Engineering Materials

Students also viewed these Mechanical Engineering questions