Question: In spur gears, the circle on which the involute is generated is called the (a) pitch circle (b) clearance circle (c) base circle (d) addendum

In spur gears, the circle on which the involute is generated is called the

(a) pitch circle

(b) clearance circle

(c) base circle

(d) addendum circle.

Step by Step Solution

★★★★★

3.39 Rating (158 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Machine Elements In Mechanical Design Questions!

Q:

What is a specific property, and what is the advantage of specific properties? (in thermodynamics )

Q:

Question 01. Which of the following statements is true aboutrack gears? A rack gear is a special case of spur gear. The teeth of a rack gear are not formed around a circle. A rack can be perceived as...

Q:

Modify the LinkedStack class and implement the ArrayStack class and the TrueStack interface mentioned in the previous exercise. Maps and filters exist in functional languages and in Smalltalk....

Q:

In spur gears, the circle on which the involute is generated is called the (A) pitch circle (B) clearance angle (C) base circle (D) addendum circle

Q:

A 4-tooth/in diametral pitch, 24-tooth pinion is to drive a 36-tooth gear. The gears are cut on the 20 full-depth involute system. Find and tabulate the addendum, dedendum, clearance, circular pitch,...

Q:

The following data refers to a pair of mating spur gears: Module pitch, m= 9; pressure angle, y = 14%; gear ratio = 5:3; pinion PCD= 162 mm. (a) Calculate: (i) The number of teeth on each wheel (ii)...

Q:

MTEC . 1 0 2 0 Engineering Design & Graphics Gear Homework Problems Problem 1 In the figure below, shaft 1 rotates at 5 4 0 0 rpm . Find the ratio between shafts 1 and 2 and the ratio between shafts...

Q:

Problem 1 ( 4 points ) : The speeds for a reduction spur gear pair are 2 0 0 0 rpm and 3 2 0 rpm , respectively. The pressure angle is designed to be 2 0 . The gears have a m = 5 m m ? teeth module...

Q:

36. Sketch and name three common tooth forms used on band saw blades. a. b. C. 39. Make a sketch of an involute spur gear and label the following items by using the corresponding letter(s) to...

Q:

Which one of the following is the correct statement? In meshing gears with involute gear teeth, the contact begins at the intersection of the (a) line of action and the addendum circle of the driven...

Q:

(a) At one-third the original distance from a positive point charge, by what factor is the electric potential changed: (1) 1/3, (2) 3, (3) 1/9, or (4) 9? Why? (b) How far from a +1.0-C charge is a...

Q:

A professor records the following final grades in one course. Construct a frequency table for the grades. . D F A B B D D D Complete the table. (Type an integer or decimal rounded to...

Q:

Nebraska Furniture wants to reduce its cash conversion cycle. Which of the following actions should it take? Question 2 options: Increases average inventory without increasing sales. Incentivizes its...

Q:

Which two statements are least appropriate? In terms of taking internal action against an employee, there are certain principles that should be followed: a. Investigate and gather the facts carefully...

Q:

Determine the Diesel cycle efficiency of an engine that has a compression ratio of 18.6 and a cut-off ratio of 2.2.

Q:

Using highly advanced materials, a research laboratory has produced a new Diesel cycle engine with a compression ratio of 58.9 and a cut-off ratio of 3.9. What is the Diesel cycle efficiency of this...

Q:

What would the Brayton cycle efficiency in Example 6.3 be if the pressure ratio was increased to 3.5? Example 6.3 A jet engine needs to produce only enough net output power to drive the aircrafts...

Q:

In NetBeans, open the DrinkMenuFile project. Take a few minutes to study the existing code in the Beverage.java and the DrinkMenuFile.java classes. The Beverage class is complete and ready to use for...

Q:

Read the news articles and Tesla's Financial Reports in last week's forum. Calculate ANY three ratios of Telsa. 0220 Update.pdf - Adobu Marubial Meather DC File Edit View Sign Window Helio Home Tools...

Q:

XV for Prime Steel Pne B C D E F Excellent Wealth Management Heartland Diamond 2x4 Lumber HITEND Company Ste Healthcare Five LLP Co. Security Ticker PRIME PULSE FIVE WOOD TEN Price 41 60 5 24 10...