CS-250 Computer Networks Fundamentals Fall 2017 Homework 1 A company is planning to implement the network shown in the attached diagram. The network consists of three LANs connected by a Router. Your task is to implement this network in Packet Tracer using the following information:

LAN 1:

Three Computers; PC_11, PC_12, and PC_13 are connected to switch S1 as follows:

PC_11:

Default Getaway: 192.110.10.115

IP Address: 192.110.10.27

Subnet Mask: 255.255.255.0

Port FastEthernet0 is connected to FastEthernet0/1 of switch S1

PC_12:

Default Getaway: 192.110.10.115

IP Address: 192.110.10.96

Subnet Mask: 255.255.255.0

Port FastEthernet0 is connected to FastEthernet0/2 of switch S1

PC_13:

Default Getaway: 192.110.10.115

IP Address: 192.110.10.93

Subnet Mask: 255.255.255.0

Port FastEthernet0 is connected to FastEthernet0/3 of switch S1

Switch S1:

Port GigabitEthernet 0/1 is connected to port GigabitEthernet0/1 of Router R1

LAN 2:

Three Computers; PC_21, PC_22, and PC_23 are connected to switch S2

PC_21:

Default Getaway: 192.120.20.45

IP Address: 192.120.20.143

Subnet Mask: 255.255.255.0

Port FastEthernet0 is connected to FastEthernet 0/1 of switch S2

PC_22:

Default Getaway: 192.120.20.45

IP Address: 192.120.20.78

Subnet Mask: 255.255.255.0

Port FastEthernet0 is connected to FastEthernet0/2 of switch S1

PC_23:

Default Getaway: 192.120.20.45

IP Address: 192.120.20.34

Subnet Mask: 255.255.255.0

Port FastEthernet0 is connected to FastEthernet0/3 of switch S1

Switch S2:

Port GigabitEthernet 0/1 is connected to port GigabitEthernet0/1 of Router R1

LAN 3:

Three Computers; PC_31, PC_32, and PC_33 are connected to switch S3

PC_31:

Default Getaway: 192.130.30.177

IP Address: 192.130.30.186

Subnet Mask: 255.255.255.0

Port FastEthernet0 is connected to FastEthernet0/1 of switch S3

PC_32:

Default Getaway: 192.130.30.177

IP Address: 192.130.30.93

Subnet Mask: 255.255.255.0

Port FastEthernet0 is connected to FastEthernet0/2 of switch S3

PC_33:

Default Getaway: 192.130.30.177

IP Address: 192.130.30.162

Subnet Mask: 255.255.255.0

Port FastEthernet0 is connected to FastEthernet0/3 of switch S3

Switch S3:

Port GigabitEthernet0/1 is connected to port GigabitEthernet0/2 of Router R1

To complete this task, follow these steps:

Use the Cisco IOS commands to change the host names of the router and three switches as follows: R1: Main_Router S1: COSET_SW S2: JHJ_SW S3: UT1_SW Connect the devices according to the attached diagram (PDF File) using the correct cables. Configure the PCs with the information provided above Use the Cisco IOS commands to configure the thee ports of the Router as follows: GigbitEtehrnet0/0: Set the IP Address to : 192.110.10.115 and the subnet mast to 255.255.255.0 Turn on the port GigbitEtehrnet0/1: Set the IP Address to : 192.120.20.45 and the subnet mast to 255.255.255.0 Turn on the port GigbitEtehrnet0/2: Set the IP Address to : 192.130.30.177 and the subnet mast to 255.255.255.0 Turn on the port Ping PC_21, PC_31 from PC_11 and make sure the pings are successful. As you implement the tasks listed above, you can check the status of your progress by clicking on Check Results at the bottom of the Instructions Window. This will take you to the Activity Results Window. Click on the Assessment Items tab to view your score and progress. To close the Activity Results window and go back to the Topology Window, click Close.

When you are done, save your file by selecting Save As from the File menu and save the file with your last name + the last 4 digits of your TNumber. For example, Sleem1234.pka. Submit the Packet Tracer file through Blackboard.