Question: I. (20 pts) Write the PLC ladder logic to control the distribution of bottles between two conveyors. A 3 position selector switch SWI is

I. (20 pts) Write the PLC ladder logic to control the distribution

I. (20 pts) Write the PLC ladder logic to control the distribution of bottles between two conveyors. A 3 position selector switch SWI is used to select the mode of operation as follows: Position #1 (IN 1) = All the bottles flow through the conveyor #1. Position #2 (IN 2) = All the bottles are transferred to conveyor #2, using a piston (OUT 3) Position # 3 (IN 3)- The bottles are distributed equally between conveyor #1 and #2. In another Words, the piston push one bottle to conv #2 and the next bottle goes to conv #1 and the sequence continues to distribute the incoming bottles equally between the 2 convetors.. Two sensors are used on the operations, refer to figure (sensor #1 = IN 4; sensor #2 = IN 5). Bottles. Sen #1 Conveyor #2 Piston Sen #2 Conveyor #1...

Step by Step Solution

★★★★★

3.50 Rating (157 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Answer 11 STOP 100 11 IN1 101 12 PISTON ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

One overnight case contains 2 bottles of aspirin and 3 bottles of thyroid tablets. A second tote bag contains 3 bottles of aspirin, 2 bottles of thyroid tablets, and I bottle of laxative tablets. If...

A 32-bit computer has two selector channels and one multiplexor channel. Each selector channel supports two magnetic disk and two magnetic tape units. The multiplexor channel has two line printers,...

Two machines are used for filling glass bottles with a soft-drink beverage. The filling processes have known standard deviations liter and liter, respectively. A random sample of bottles from machine...

A temperature control system consists of four thermostats controlling three heating units. The thermostat contacts are set to close at 50. 60 , 70 , and 80 F, respectively. The PLC ladder logic...

Create two PLC ladder logic diagrams that use PLC coils and contacts to seal outputs. Then, you will use the Logix Pro simulation software to create the PLC ladder logic diagrams and verify their...

The logic you designed in Project 3 needs to be designed in Studio 5000 and implemented in hardware.Design: 1)PLC Ladder Logic tostart the motor forward. Oncethestop button is pressed, the motor...

What instruction in the main PLC ladder logic diagram is used to call a subroutine? Name it and draw it in block form.

A commuter train travels between two downtown stations. Because the stations are only 1.00 km apart, the train never reaches its maximum possible cruising speed. During rush hour the engineer...

A heat engine operates between two reservoirs at T2 = 600 K and T1 = 350 K. It takes in 1 000 J of energy from the higher-temperature reservoir and performs 250 J of work. Find (a) The entropy change...

Economists use a cumulative distribution called a Lorenz curve to describe the distribution of income between households in a given country. Typically, a Lorenz curve is defined on [0, 1] with...

What is operating capital, and why is it important?

Nautical Dream Boat Supply uses the periodic inventory method. The adjusted trial balance of Nautical Dream Boat Supply at December 31, 2016, follows: Requirements 1. Journalize the required closing...

An agent that represents only 1 insurance company is A ) a general agent B ) a captive agent C ) a special agent D ) a broker 2 Check for Review

For the transfer function below, find the constraints on K 1 and K 2 such that the function will have only two j poles. K1s + K2 T(s) = s4 + K1s + s? + K2s + 1

Write a function that accepts temperature in degrees Fahrenheit (F) and computes the corresponding value in degrees Celsius (C). The relation between the two is Be sure to test your function. 5 ...

The current in a 25-mH inductor is given by the expressionsM i(t)=0 t 0 Find (a) the voltage across the inductor, (b) the expression for the energy stored in it.

The velocity of a particle which moves along the s-axis is given by v = 2 4t + 5t 3/2 , where t is in seconds and v is in meters per second. Evaluate the position s, velocity v, and acceleration a...

Show that every DCFG is an unambiguous CFG.

Given the functions f open parentheses x close parentheses equals x squared plus 5 and g open parentheses x close parentheses equals 11 minus 3 x comma find f open parentheses short dash 2 close...

especially , 3rd and 4th question please 1. 25 pts] Write an MSP430 C function that implements bubble sort of N words: bubbleSort(short int *inpPtr, short int *outPtr, short int N) 2. [25 pts] 2.1...

Turn in the following Python programs (only the ".py" files) along with their output: ___________________________________________________________________________________________ Problem 1 (20 pts)...

For this assignment you will be required to write functions which solve each of the following problems. You must place all of your functions in one project. If you use any code that you find online,...

Note that if you use any Python programming techniques beyond those covered in class, you must supply comments demonstrating that you understand how and why your code works as intended How to submit...

Computer architecture questions using Marie simulator. on number 2 do the writing of multiple of 3 into an array. On 3 come up with a new instruction and give details explaining everything and same...

Please take time to answer and produce correct result to the question.please show resulting code and output on screen The requirement code are shown below. Grading (100 pts): You can earn points as...