FREE Trial
Answered step by step
Verified Expert Solution
Link Copied!

Question

1 Approved Answer

The force F acting on the part shown in the figure is 12.5 KN, the force P is 20 KN and the torsional moment T

The force F acting on the part shown in the figure is 12.5 KN, the force P is 20 KN and the torsional moment T is 240 Nm. Since the yield strength of the part material is 725 MPa, what is the safety factor at point B according to the Von-Misses criterion?

Step by Step Solution

There are 3 Steps involved in it

Step: 1

blur-text-image

Get Instant Access to Expert-Tailored Solutions

See step-by-step solutions with expert insights and AI powered tools for academic success

Step: 2

blur-text-image_2

Step: 3

blur-text-image_3

Ace Your Homework with AI

Get the answers you need in no time with our AI-driven, step-by-step assistance

Get Started

Recommended Textbook for

Thermodynamics An Engineering Approach

Thermodynamics An Engineering Approach

Authors: Yunus A. Cengel, Michael A. Boles

8th edition

73398179, 978-0073398174

More Books

Students also viewed these Mechanical Engineering questions

Question

★★★★★
Consider a simple harmonic oscillator. Calculate the time averages of the kinetic and potential energies over one cycle, and show that these quantities are equal. Why is this a reasonable result?...

Answered: 1 week ago

Question

★★★★★
Find the particular solution of the differential equation that satisfies the initial condition(s). f (x) = 3x 2 , f(1) = 2, f(2) = 3

Answered: 1 week ago

Question

★★★★★
=+31.13. Suppose that X1, X2 ,... are independent and assume the values +1 with probability ; each, and let X = 2- 1X ,, /2". Show that X is uniformly dis-

Answered: 1 week ago

Question

★★★★★
You cool a l00.0-g slug of red-hot iron (temperature 745C) by dropping it into an insulated cup of negligible mass containing 75.0 g of water at 20.0C. Assuming no heat exchange with the...

Answered: 1 week ago

Question

★★★★★
The force F acting on the part shown in the figure is 12.5 KN, the force P is 20 KN and the torsional moment T is 240 Nm. Since the yield strength of the part material is 725 MPa, what is the safety...

Answered: 1 week ago

Question

★★★★★
Sunland, Inc. had pre-tax accounting income of $2100000 and a tax rate of 40% in 2018, its first year of operations. During 2018 the company had the following transactions: Received rent from Jane,...

Answered: 1 week ago

Question

★★★★★
Joaquin goes for a job interview and is surprised that the interviewer asks him about his personal standards regarding how he would handle certain situations. He expected that the focus would be on...

Answered: 1 week ago

Question

★★★★★
Using this ER-Diagram, write an SQL Statement using CONSTRAINTS command and show atleast 1 data of the database. Write down below the SQL Statements and commands that was used. PDiagnosis PAddress...

Answered: 1 week ago

Question

★★★★★
1. (a)(i) What problem has been brought about by uncontrolled mining of minerals in Kenya? (ii) Where is fluorspar mined in Kenya? (iii) Describe how trona is mined and processed in Magadi (b) (i)...

Answered: 1 week ago

Question

★★★★★
In 2001, a commercial aircraft lost all power while flying at 10,000 m over the Atlantic Ocean, about 100 km from the Azores Islands. The skilled pilot put the plane into a gliding mode and...

Answered: 1 week ago

Question

★★★★★
Domino's Pizza franchises in New York were sued by the state of New York in 2016for wage theft at 10 stores.Under New York law, a corporation and a franchiser are joint employers if they meet certain...

Answered: 1 week ago

Question

★★★★★
examine a variety of flexible working arrangements and assess their usefulness and impact for employers and employees

Answered: 1 week ago

Question

★★★★★
understand the basis of the contract of employment and know what should be in a contract of employment

Answered: 1 week ago

Question

★★★★★
describe the main employment rights as stated in the law

Answered: 1 week ago

Previous Question Next Question