Question: two push buttons are connected to pin 3 and 4 of the arduino. an led is connected to pin 13. The led must switch on

two push buttons are connected to pin 3 and 4 of the arduino. an led is connected to pin 13.
The led must switch on when the push button connected to pin 3 is pressed 3 times and the push button connected to pin 4 is pressed 6 times
i want the code

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Databases Questions!

Q:

Question 1: Two push buttons are connected to Pins 3 and 4 of the Arduino. An LED is connected to Pin 13. The LED must switch on when the push button connected to Pin 3 is pressed 3 times and the...

Q:

In this assignment, you will develop a simple traffic light control system for a four - way street intersection using Arduino Uno board. At the minimum, you must prepare 2 sets of traffic lights (...

Q:

Lab1 15 Components Required: 1. Arduino UNO 1 2. Common anode single digit 7 segment display. 1 3. Assorted resistors (any value less than 500 Ohms) 7 4. Jumper wires 5. Push to ON switches 2 6. Pull...

Q:

Please write a code to comply with the MSP4302553. LAB 02 Port l/0 Goals: Light both the onboard LEDs with the onboard button Connect two other buttons to Port 1 of the micro. Use a polling scheme...

Q:

This is the main circuit in logism; which has 2 keypads 3 hex digit displays. The displays show the numbers enters on keypad 1 and keypad 2 and the contents of the DR register. A switch for carry-in...

Q:

Design the HW and SW of an embedded system that has two push buttons that should be connected to the INT 0 and INT 1 pins in the Arduino board. The push buttons should be debounced in software...

Q:

Design the HW and SW of an embedded system that has two push buttons that should be connected to the INT 0 and INT 1 pins in the Arduino board. The push buttons should be debounced in software...

Q:

Q3. (10Pts) Let's consider a LED is connected toan Arduino pin 10 and a push button switch is connected to pin 3. Write Arduino codes to control (on/off the LED

Q:

This is aproject for digital logic can you please solve Part F and Part G this a Digital logic mini project A. Objectives The objectives of this laboratory are to introduce the students to The...

Q:

1. a PIC18F has 8 LEDs connected to Port A and 8 switches connected to Port B, write a C program for the following task : The code will continually read the value of the switches, if the value is...

Q:

Do you think the India government spending constrained by this national preference policy has a bigger effect on Indian output than unconstrained Indian government spending What could happen if this...

Q:

The lever AB is welded to the bent rod BCD which is supported by bearing E and by cable DG. Assuming that the bearing can exert an axial thrust and couples about axes parallel to the x and z axes,...

Q:

Jennifer is a certified managerial accountant who works for a global manufacturer. She attends a five day conference every year to earn continuing education credits required to maintain her...

Q:

Seved Help 14 Wisconsin Snowmobile Corp. is considering a switch to level production Cost efficiencies would occur under level production, and aftertax costs would decline by $31,500, but inventory...

Q:

If the tax rate is 40 percent, compute the beforetax real interest rate and the after-tax real interest rate in each of the following cases. a. The nominal interest rate is 10 percent and the...

Q:

Assume that the reserve requirement is 20%. Also assume that banks do not hold excess reserves and there is no cash held by the public. The Federal Reserve decides that it wants to expand the money...

Q:

It is often suggested that the Federal Reserve try to achieve zero inflation. If we assume that velocity is constant, does this zero-inflation goal require that the rate of money growth equal zero?...