Answered step by step

Verified Expert Solution

Link Copied!

Question

1 Approved Answer

Posted on Oct 02, 2024

You bought a share one year ago for $ 31.62 and sold it today for $ 33.16 It paid a $ 1.59 per share dividend

You bought a share one year ago for $ 31.62 and sold it today for $ 33.16 It paid a $ 1.59 per share dividend today. What was your realised return?

Step by Step Solution

There are 3 Steps involved in it

Step: 1

Get Instant Access to Expert-Tailored Solutions

See step-by-step solutions with expert insights and AI powered tools for academic success

Step: 2

Step: 3

Ace Your Homework with AI

Get the answers you need in no time with our AI-driven, step-by-step assistance

Get Started

Recommended Textbook for

Bitcoinvest Or Not Answers To Crucial Questions

Authors: Mr Panayotis Vasileios Sofianopoulos

1st Edition

1713251752, 978-1713251750

More Books

Students also viewed these Finance questions

Question

★★★★★

If F1 = F2 = 30 lb. determine the angles ? and ? so that the resultant force is directed along the positive x axis and has a magnitude of FR = 20 lb.. 15 8 F

Answered: 1 week ago

Question

★★★★★

For each situation, identify the management assertion(s) most likely affected. Assertions: A. Cutoff B. Accuracy C. Completeness D. Existence E. Valuation F. Occurrence Assertion(s) (A,B,C,D,E,F)...

Answered: 1 week ago

Question

★★★★★

2. The alignment propositions that form the basis for the people-oriented management functions are as follows: Proposition No. 1: Ethical behavior, transparency, and trust Proposition No. 2: Clearly...

Answered: 1 week ago

Question

★★★★★

Old Camp Company manufactures awnings for its own line of tents. The company is currently operating at capacity and has received an offer from one of its suppliers to make the 10,000 awnings it needs...

Answered: 1 week ago

Question

★★★★★

You bought a share one year ago for $ 31.62 and sold it today for $ 33.16 It paid a $ 1.59 per share dividend today. What was your realised return?

Answered: 1 week ago

Question

★★★★★

Given the Center-Tapper full-Wave rectifier in figure 1, use EasyEDA software to redesign the circuit and simulate the voltage waveforms across each half of the secondary winding and the across R...

Answered: 1 week ago

Question

★★★★★

You are required to design a shell and tube heat exchanger having a rectangular cross section as shown in figure 1 below. The heat exchanger uses water as the cooling fluid to reduce the temperature...

Answered: 1 week ago

Question

★★★★★

The Bakeoff Case Read "The Bakeoff" case and post approximately 1 page of text (about 4 paragraphs) answering the following questions SOLELY based on the case. Do not use other references. What were...

Answered: 1 week ago

Question

★★★★★

1. Determine the magnitude and direction of the force that must be applied to the bottom of the gate shown below to keep the gate closed. 3.4 m Water 1.5 m wide gate Hinge T 0.75 m

Answered: 1 week ago

Question

★★★★★

Lynda is a manager of an investment center. Her division has been performing below expectations recently because one of its larger projects has not been as successful as anticipated. Given the poor...

Answered: 1 week ago

Question

★★★★★

Question 2 Determine the first two critical speeds for the shaft shown in figure 1 below. Young's modulus for steel should be taken as 200GN/m2. Show all the calculations and state all your...

Answered: 1 week ago

Previous Question Next Question