Why is single-piece flow necessary?

Question:

Fantastic news! We've Found the answer you've been seeking!

Step by Step Answer:

Related Book For book-img-for-question

Materials and process in manufacturing

ISBN: 978-0471656531

9th edition

Authors: E. Paul DeGarmo, J T. Black, Ronald A. Kohser

See More Books

Question Posted: May 24, 2016 06:41 AM

See More Questions

The box is to be made from a single piece of sheet metal. Repeat Problem Design a box that will contain a 4 in. 6 in. 3 in. volume. The box is to be produced from two pieces of sheet metal and will...
If the first step is to form single-piece flow cells, what will be the consequence of all the hidden variations that existed in the job shop design?
Why Don't We Diffract? (a) Calculate the de Broglie wavelength of a typical person walking through a doorway. Make reasonable approximations for the necessary quantities. (b) Will the person in part...
In Problem 3.67 on page 135, you were introduced to a tea-bag-filling operation. An important quality characteristic of interest for this process is the weight of the tea in the individual bags. The...
Starz Department Store is located near the Towne Shopping Mall. At the end of the company's calendar year on December 31, 2014, the following accounts appeared in two of its trial balances....
Explain how variance analysis can provide an integrated overview of overhead-cost variances
What is the difference between the concepts of absolute advantage and comparative advantage?.L01
In Figure a sled is held on an inclined plane by a cord pulling directly up the plane. The sled is to be on the verge of moving up the plane. In Fig. 6-34, the magnitude F required of the cord's...
Please do question (iii), Thanks! Wing Wine Beverage Club Unadjusted Trial Balance For the period ended 31 December 2021 Trial Balance Unit = HK$ Dr. Cr. 163,000 163,570 240,000 547,260 28,000 81,000...
1. Using the trends identified by Siemens in Figure 1 (or other environmental forces you consider important) which would you consider to be key drivers for change for Siemens and why? 2. Are there...
If a machine's processing time exceeds cycle time in a manufacturing cell, what after natives might the manufacturing engineer consider to ensure that a cell meets the necessary cycle time?
Identify the machine design requirements for cells (for example, a walkaway switch).
Match each of the key terms with the definition that best fits it. ___________ A system that integrates individual traditional business functions into a series of modules so that a single transaction...
Low Desert Pottery works makes a variety of pottery products that it sells to retailers. The company uses a job-order costing system in which departmental predetermined overhead rates are used to...
ASSESSMENT CPCCBC5002A Monitor costing systems on medium rise building and construction projects Please provide answer to Part 2 - Monitor expenditure for a medium-rise project as per below...
Questions 6-8 refer to the same problem A sinusoidal wave with wavelength 2 m and amplitude 5 mm is traveling along the x axis. The wave is traveling in the -x direction at a speed of 2m/s At t = Os,...
Consider a circuit where one or more capacitors is discharged through a light bulb filament with a resistance of 3.0 0.3 . Assume that the resistance of the filament is constant (to within the stated...
3. For a vibrating string of length with fixed ends, each mode of vibration can be written as where wk ux(x, t) = M* sin(wxt + k) sin(x) and Mk, Ok are determined by initial conditions. For all k >...
A power electronics device turns off 50 A in 200 s and builds up the voltage from zero to 110 V in 220 s. Determine the di/dt and dv/dt stresses on the device.
Planning: Creating an Audience Profile; Collaboration: Team Projects. Compare the Facebook pages of three companies in the same industry. Analyze the content on all available tabs. What can you...
An open water jet exits from a nozzle into sea-level air, as shown, and strikes a stagnation tube. If the centerline pressure at section (1) is 110 kPa and losses are neglected, estimate (a) the mass...
A venturi meter, shown in Fig P3.165, is a carefully designed constriction whose pressure difference is a measure of the flow rate in a pipe. Using Bernoullis equation for steady incompressible flow...
A wind tunnel draws in sea-level standard air from the room and accelerates it into a 1-m by 1-m test section. A pressure transducer in the test section wall measures Δp = 45 mm water between...
Transcribed image text
QUESTION 20 Assume a company reported the following results Sales Net operating income Average operating assets Margin Turnover Return on investment (ROI) 5300,000 2 $240.000 40% ? 2 What is the net...
2. Using the graph provided below, determine the fixed cost, the total variable cost, the variable cost per unit, and the TOTAL COST to produce 60 units. Fixed Cost ______________ Variable Cost...

Why is single-piece flow necessary?

Question:

Step by Step Answer:

Single piece flow is necessary in a cell because it is the basis ...View the full answer

Materials and process in manufacturing

Students also viewed these Materials Science Engineering questions