Question: In order to speed up a system without changing the percent overshoot, where must the compensated systems poles on the s-plane be located in comparison

In order to speed up a system without changing the percent overshoot, where must the compensated system’s poles on the s-plane be located in comparison to the uncompensated system’s poles?

Step by Step Solution

★★★★★

3.44 Rating (163 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

If the typical phase margin is around 60 degrees then the minimum phase margin will typica... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Control Systems Engineering Questions!

If the work required to speed up a car from 10 km/h to 20 km/h is 5.0 x 103 J, what would be the work required to increase the cars speed from 20 km/h to 30 km/h?

A light plane must reach a speed of 33m/s for takeoff. How long a runway is needed if the (constant) acceleration is 3.0m/s2?

A plane figure S is to be translated by And then the resulting figure translated by (a) Determine the 3 x 3 matrix M in homogeneous form that will perform this composition of translations, (b) Can...

In Problem 67, Chapter 7 (Figure P7.31), the block diagram of a cascade scheme for the speed control of an HEV (Preitl, 2007) was represented as a unity feedback system. In that diagram the output of...

Consider the unity feedback system of Figure P9.1 with The system is operating at 20% overshoot. Design a compensator to decrease the settling time by a factor of 2 without affecting the percent...

Consider the unity - feedback system above with \ [ G ( s ) = \ frac { K } { s ( s + 2 0 ) ( s + 4 0 ) } \ ] The system is operating at \ ( 2 0 \ % \ ) overshoot. Design a compensator to decrease the...

For the exclusive use of A. Young NA0232 Daktronics (A): The U.S. Digital Signage Industry in 2010 Joseph Kavanaugh, Sam Houston State University Joshua Warne and Carol J. Cumber, South Dakota State...

Reference: Essentials of International Human Resource Management by David C. Thomas and Mila B. Lazarova Peter Hanson: Building a World-Class Product Development Centre for Hi Tech Systems in China "...

Kindly answer the following question from facility management without explanations : in which of the following project phases are a project's end results identified? a. Define b. Do c. Plan d. Act An...

Read the case: The dream's door: a case of a MNC in Poland Introduction It was a nice sunny morning in Zurich. DAK Europe's chairman gathered all of his board members around a large table and went...

Airbnb in 2016: A BusinessModel for the Sharing Economy In the future, you will own what[assets] you want responsibility for,"commented CEO and founder ofAirbnb, Brian Chesky, concerning the sharing...

Financing Analysis In order to launch the new gadget line, Acme is securing investor financing to cover the first year of fixed costs from private investors. A first private investor is willing to...

Predictable cycles in stock price movements 1 ) tend to persist for a long time 2 ) tend to self - destruct as soon as investors recognize them 3 ) never appear, since stock returns change randomly 0...

2. Jeet Kumar is the administrator of data warehousing at a big regional bank. He was appointed 5 years ago to implement a data warehouse to support the banks CRM business strategy. Using the data...

A milling operation is carried out on a 10. inch long, 3.0 inch wide slab of aluminum alloy. The cutter feed is 0.01 in/tooth, and the depth of cut is 0.125 inches. The cutter is wider than the slab...

A part 275. mm long and 75. mm wide is to be milled with a 10-toothed cutter 75. mm in diameter using a feed of 0.10 mm/tooth at a cutting speed of 40. x 10 3 mm/min. The depth of cut is 5.0 mm....

In the face-milling operation shown below the cutter is 1.5 inches in diameter and the cast iron workpiece is 7.0 inches long and 3.75 inches wide. The cutter has 8 teeth and rotates at 350 RPM. The...

Ultratech, Inc., manufactures several different types of printed circuit boards; however, two of the boards account for the majority of the companys sales. The first of these boards, a television...

What is the p value HW Score: 16.86%, 0.84 14.5.32 Question Help Consider the following set of ordered pairs. x 2 6 1 3 30 y 5 10 4 8 6 Assuming that the regression equation is y = 2.957 + 1.214x and...

Carlsbad Corporation's sales are expected to increase from $5 million in 2019 to $6 million in 2020, or by 20%. Its assets totaled $3 million at the end of 2019. Carlsbad is at full capacity, so its...